Arch: Armatura diritta
Armatura dritta |
Posizione nel menu |
---|
Arch → Strumenti armatura |
Ambienti |
Arch |
Avvio veloce |
None |
Vedere anche |
Armatura, Armatura a U, Armatura a L, Armatura sagomata, Staffe armatura, Armatura elicoidale |
Questo comando fa parte del Addon Reinforcement, che è possibile installare tramite il menu Strumenti → Addons Manager |
Descrizione
Lo strumento Armatura dritta crea una armatura diritta in un elemento strutturale selezionato.
This command is part of the Reinforcement Addon, that you can install with the Addon Manager via the menu Tools → Addon manager → Reinforcement.
Utilizzo
- Creare un elemento Struttura
- Selezionare una qualsiasi faccia della struttura
- Selezionare Armatura dritta dagli strumenti Armatura
- Sul lato sinistro dello schermo appare un pannello delle azioni come il seguente
- Selezionare l'orientamento desiderato
- Fornire i dati per front cover, right side cover, left side cover, bottom cover, top cover, rounding factor and diameter of the rebar
- Selezionare la modalità di distribuzione per la quantità e per la spaziatura
- Se la spaziatura è selezionata, l'utente può anche optare per una spaziatura personalizzata
- Cliccare sulla faccia selezionata serve per verificare o modificare la faccia per la distribuzione dell'armatura
- Cliccare OK o Apply per generare l'armatura
- Cliccare Cancel per uscire dal pannello delle azioni
Taskview panel for the Arch Rebar Straight tool
Proprietà
- DatiOrientation: Decide l'orientamento dell'armatura (es. in basso, in alto, a destra e a sinistra).
- DatiFront Cover: La distanza tra l'armatura e la faccia selezionata. Copriferro anteriore
- DatiRight Cover: La distanza tra l'estremità destra della barra di destra e la faccia destra della struttura. Copriferro destro
- DatiLeft Cover: La distanza tra l'estremità sinistra della barra di sinistra e la faccia sinistra della struttura. Copriferro sinistro
- DatiBottom Cover: La distanza tra l'armatura e la parte inferiore della struttura. Copriferro inferiore
- DatiTop Cover: La distanza tra l'armatura e la parte superiore della struttura. Copriferro superiore
- DatiRounding: Il raggio di curvatura da applicare agli angoli delle barre, espresso quantità di diametro delle barre.
- DatiAmount: La quantità di barre.
- DatiSpacing: La distanza tra gli assi di ogni barra.
Script
Lo strumento Armatura dritta può essere usato nelle macro e dalla console python utilizzando la seguente funzione:
Rebar = makeStraightRebar(f_cover, coverAlong, rt_cover, lb_cover,
diameter, amount_spacing_check, amount_spacing_value, orientation="Horizontal",
structure=None, facename=None)
- Creates a
Rebar
object from the givenstructure
, which is an Arch Structure, andfacename
, which is a face of that structure.- If no
structure
norfacename
are given, it will take the user selected face as input.
- If no
f_cover
,coverAlong
,rt_cover
, andlb_cover
are inner offset distances for the rebar elements with respect to the faces of the structure.f_cover
is the frontal cover offset.coverAlong
is a tuple(position, value)
that defines the offset value in one position (top, bottom, left, right) depending on theorientation
.rt_cover
is either the right or the top cover offset, depending on the value ofcoverAlong
andorientation
.lb_cover
is either the left or the bottom cover offset, depending on the value ofcoverAlong
andorientation
.
diameter
is the diameter of the reinforcement bars inside the structure.amount_spacing_check
if it isTrue
it will create as many reinforcement bars as given byamount_spacing_value
; if it isFalse
it will create reinforcement bars separated by the numerical value ofamount_spacing_value
.amount_spacing_value
specifies the number of reinforcement bars, or the value of the separation between them, depending onamount_spacing_check
.orientation
specifies the orientation of the rebar; it can be"Horizontal"
or"Vertical"
.
Depending on the orientation of the rebar, the function can be called in two general ways by setting coverAlong
appropriately.
The rebar is horizontal
Rebar = makeStraightRebar(f_cover, ("Top Side", value), right_cover, left_cover, ...)
Rebar = makeStraightRebar(f_cover, ("Bottom Side", value), right_cover, left_cover, ...)
coverAlong
is a tuple with either a"Top Side"
or a"Bottom Side"
offsetvalue
.- In this case
rt_cover
refers to theright_cover
offset, andlb_cover
refers to theleft_cover
offset.
The rebar is vertical
Rebar = makeStraightRebar(f_cover, ("Left Side", value), top_cover, bottom_cover, ...)
Rebar = makeStraightRebar(f_cover, ("Right Side", value), top_cover, bottom_cover, ...)
coverAlong
is a tuple with either a"Left Side"
or a"Right Side"
offsetvalue
.- In this case
rt_cover
refers to thetop_cover
offset, andlb_cover
refers to thebottom_cover
offset.
Example horizontal
import Arch, Draft, StraightRebar
Structure = Arch.makeStructure(length=1000, width=1000, height=400)
Structure.ViewObject.Transparency = 80
FreeCAD.ActiveDocument.recompute()
Rebar = StraightRebar.makeStraightRebar(50, ("Bottom Side", 20), 100, 100,
12, True, 5, "Horizontal", Structure, "Face4")
Rebar.ViewObject.ShapeColor = (0.9, 0.0, 0.0)
Rebar2 = StraightRebar.makeStraightRebar(50, ("Bottom Side", 50), 100, 100,
12, True, 5, "Horizontal", Structure, "Face6")
Rebar2.ViewObject.ShapeColor = (0.0, 0.0, 0.9)
Example vertical
import Arch, Draft, StraightRebar
Structure2 = Arch.makeStructure(length=1000, width=1000, height=400)
Structure2.ViewObject.Transparency = 80
Draft.move(Structure2, FreeCAD.Vector(1500, 0, 0))
FreeCAD.ActiveDocument.recompute()
Rebar3 = StraightRebar.makeStraightRebar(50, ("Left Side", 20), 100, 100,
12, True, 5, "Vertical", Structure2, "Face4")
Rebar3.ViewObject.ShapeColor = (0.9, 0.5, 0.0)
Rebar4 = StraightRebar.makeStraightRebar(50, ("Left Side", 50), 100, 100,
12, True, 5, "Vertical", Structure2, "Face6")
Rebar4.ViewObject.ShapeColor = (0.0, 0.5, 0.5)
Cambiare le proprietà di una armatura Straight.
editStraightRebar(Rebar, f_cover, coverAlong, rt_cover, lb_cover,
diameter, amount_spacing_check, amount_spacing_value, orientation,
structure=None, facename=None)
Rebar
is a previously createdStraightRebar
object.- The other parameters are the same as required by the
makeStraightRebar()
function. structure
andfacename
may be omitted so that the rebar stays in the original structure.
Example:
import StraightRebar
StraightRebar.editStraightRebar(Rebar, 50, ("Top Side", 20), 100, 100,
24, True, 7, "Horizontal")
StraightRebar.editStraightRebar(Rebar2, 50, ("Top Side", 50), 100, 100,
24, True, 7, "Horizontal")
StraightRebar.editStraightRebar(Rebar3, 50, ("Right Side", 20), 100, 100,
24, True, 7, "Vertical")
StraightRebar.editStraightRebar(Rebar4, 50, ("Right Side", 50), 100, 100,
24, True, 7, "Vertical")