Reinforcement BentShapeRebar/it: Difference between revisions
Renatorivo (talk | contribs) No edit summary |
Renatorivo (talk | contribs) (Created page with "{{Arch Tools navi/it}}") |
||
Line 122: | Line 122: | ||
{{docnav/it|[[Arch_Rebar_LShape/it|Armatura a L]]|[[Arch_Rebar_Stirrup/it|Staffe armatura]]|[[Arch_Module/it|Arch]]|IconL=Arch_Rebar_LShape.svg |IconC=Workbench_Arch.svg |IconR=Arch_Rebar_Stirrup.svg}} |
{{docnav/it|[[Arch_Rebar_LShape/it|Armatura a L]]|[[Arch_Rebar_Stirrup/it|Staffe armatura]]|[[Arch_Module/it|Arch]]|IconL=Arch_Rebar_LShape.svg |IconC=Workbench_Arch.svg |IconR=Arch_Rebar_Stirrup.svg}} |
||
{{Arch Tools navi}} |
{{Arch Tools navi/it}} |
||
{{Userdocnavi}} |
{{Userdocnavi}} |
Revision as of 16:58, 6 April 2019
Armatura sagomata |
Posizione nel menu |
---|
Arch → Armatura → Armatura sagomata |
Ambiente |
Arch, BIM |
Avvio veloce |
Nessuno |
Introdotto nella versione |
0.17 |
Vedere anche |
Staffe armatura, Armatura |
Descrizione
This command is part of the Reinforcement Addon, that you can install with the Addon Manager, via the menu Tools → Addon manager → Reinforcement.
Utilizzo
- Creare un elemento Struttura
- Selezionare una qualsiasi faccia della struttura
- Selezionare Armatura sagomata dagli strumenti Armatura
- Sul lato sinistro dello schermo appare un pannello delle azioni come il seguente
- Selezionare l'orientamento desiderato
- Fornire i dati per front cover, right side cover, left side cover, bottom cover, top cover, rounding factor and diameter of the rebar
- Selezionare la modalità di distribuzione per la quantità e per la spaziatura
- Se la spaziatura è selezionata, l'utente può anche optare per una spaziatura personalizzata
- Cliccare sulla faccia selezionata serve per verificare o modificare la faccia per la distribuzione dell'armatura
- Cliccare OK o Apply per generare l'armatura
- Cliccare Cancel per uscire dal pannello delle azioni
Taskview panel for the Arch Rebar BentShape tool
Proprietà
- DatiOrientation: Decide l'orientamento dell'armatura (es. in basso, in alto, a destra e a sinistra).
- DatiFront Cover: La distanza tra l'armatura e la faccia selezionata. Copriferro anteriore
- DatiRight Cover: La distanza tra l'estremità destra della barra di destra e la faccia destra della struttura. Copriferro destro
- DatiLeft Cover: La distanza tra l'estremità sinistra della barra di sinistra e la faccia sinistra della struttura. Copriferro sinistro
- DatiBottom Cover: La distanza tra l'armatura e la parte inferiore della struttura. Copriferro inferiore
- DatiTop Cover: La distanza tra l'armatura e la parte superiore della struttura. Copriferro superiore
- DatiAnchor Length: È la lunghezza del braccio della barra piegata.
- DatiBent Angle: L'angolo di piega
- DatiAmount: La quantità di barre.
- DatiSpacing: La distanza tra gli assi di ogni barra.
Script
Lo strumento Armatura sagomata può essere usato nelle macro e dalla console python utilizzando la seguente funzione:
Rebar = makeBentShapeRebar(f_cover, b_cover, l_cover, r_cover,
diameter, t_cover, bentLength, bentAngle, rounding, amount_spacing_check, amount_spacing_value, orientation="Bottom",
structure=None, facename=None)
- L'armatura sagomata ha quattro orientamenti diversi:
- Basso
- Alto
- Sinistra
- Destra
- Aggiunge un oggetto Armatura sagomata (Bent Shape) all'oggetto strutturale specificato.
- Se Structure e Facename non sono fornite, prende come input la faccia selezionata dall'utente.
- Here CoverAlong argument is having type tuple.
- Restituisce il nuovo oggetto Rebar.
Example
import FreeCAD, Arch, BentShapeRebar
Structure = Arch.makeStructure(length=1000, width=1000, height=100)
Structure.ViewObject.Transparency = 80
FreeCAD.ActiveDocument.recompute()
Rebar = BentShapeRebar.makeBentShapeRebar(50, 20, 20, 20,
8, 40, 100, 135, 2, True, 4, "Bottom", Structure, "Face4")
Rebar.ViewObject.ShapeColor = (0.9, 0.0, 0.0)
Rebar2 = BentShapeRebar.makeBentShapeRebar(50, 40, 20, 20,
8, 20, 100, 135, 2, True, 4, "Bottom", Structure, "Face6")
Rebar2.ViewObject.ShapeColor = (0.0, 0.0, 0.9)
Edition of the rebar
You can change the properties of the rebar with the following function
editBentShapeRebar(Rebar, f_cover, b_cover, l_cover, r_cover,
diameter, t_cover, bentLength, bentAngle, rounding, amount_spacing_check, amount_spacing_value, orientation,
structure=None, facename=None)
Rebar
is a previously createdBentShapeRebar
object.- The other parameters are the same as required by the
makeBentShapeRebar()
function. structure
andfacename
may be omitted so that the rebar stays in the original structure.
import BentShapeRebar
BentShapeRebar.editBentShapeRebar(Rebar, 50, 20, 20, 20,
12, 20, 100, 155, 2, True, 6, "Top")
BentShapeRebar.editBentShapeRebar(Rebar2, 50, 35, 20, 20,
12, 35, 100, 155, 2, True, 6, "Top")
Arch
- Elements: Wall, Structure, Curtain Wall, Window, Roof, Space, Stairs, Equipment, Frame, Fence, Truss, Profile, Pipe, Pipe Connector
- Reinforcements: Straight Rebar, U-Shape Rebar, L-Shape Rebar, Stirrup, Bent-Shape Rebar, Helical Rebar, Column Reinforcement, Beam Reinforcement, Slab Reinforcement, Footing Reinforcement, Custom Rebar
- Panels: Panel, Panel Cut, Panel Sheet, Nest
- Materials: Material, Multi-Material
- Organization: Building Part, Project, Site, Building, Level, External reference, Section Plane, Schedule
- Axes: Axis, Axes system, Grid
- Modification: Cut with plane, Add component, Remove component, Survey
- Utilities: Component, Clone component, Split Mesh, Mesh to Shape, Select non-manifold meshes, Remove Shape from Arch, Close Holes, Merge Walls, Check, Toggle IFC Brep flag, 3 Views from mesh, Create IFC spreadsheet, Toggle Subcomponents
- Additional: Preferences, Import Export Preferences (IFC, DAE, OBJ, JSON, 3DS, SHP), IfcOpenShell, IfcPlusPlus, Arch API
User documentation
- Getting started
- Installation: Download, Windows, Linux, Mac, Additional components, Docker, AppImage, Ubuntu Snap
- Basics: About FreeCAD, Interface, Mouse navigation, Selection methods, Object name, Preferences, Workbenches, Document structure, Properties, Help FreeCAD, Donate
- Help: Tutorials, Video tutorials
- Workbenches: Std Base, Arch, Assembly, CAM, Draft, FEM, Inspection, Mesh, OpenSCAD, Part, PartDesign, Points, Reverse Engineering, Robot, Sketcher, Spreadsheet, Surface, TechDraw, Test Framework
- Hubs: User hub, Power users hub, Developer hub