PartDesign Pad/es: Difference between revisions
(Created page with "===Dimension===") |
(Created page with "Introduce un valor numérico para la longitud del saliente. La dirección por defecto para la extrusión es saliendo del soporte, pero se puede cambiar seleccionando la opció...") |
||
Line 46: | Line 46: | ||
===Dimension=== |
===Dimension=== |
||
Introduce un valor numérico para la longitud del saliente. La dirección por defecto para la extrusión es saliendo del soporte, pero se puede cambiar seleccionando la opción '''Invertir'''. Las extrusiones se realizan normales [http://en.wikipedia.org/wiki/Surface_normal normales] al plano de definición del croquis. |
|||
Enter a numeric value for the length of the pad. The default direction for extrusion is away (outside of) the support, but it can be changed by ticking the '''Reversed''' option. Extrusions occur [http://en.wikipedia.org/wiki/Surface_normal normal] to the defining sketch plane. With the option '''Symmetric to plane''' the pad will extend half of the given length to either side of the sketch plane. Negative dimensions are not possible. Use the '''Reversed''' option instead. |
|||
Con la opción '''Simétrico al plano''' el saliente se extenderá la mitad de la dimensión indicada hacia cada lado del plano de croquis. |
|||
No es posible indicar dimensiones negativas. Utiliza en cambio la opción '''invertir'''. |
|||
====Two dimensions==== |
====Two dimensions==== |
Revision as of 12:07, 5 November 2019
PartDesign_Pad |
Ubicación en el Menú |
---|
Diseño de Piezas → Saliente |
Entornos de trabajo |
Diseño de Piezas |
Atajo de teclado por defecto |
Ninguno |
Introducido en versión |
- |
Ver también |
Ninguno |
Introducción
'Crea un saliente a partir de un croquis seleccionado' - Esta herramienta toma un croquis seleccionado como entrada (el 'croquis de definición'), y crea a partir de él un 'saliente'. Un saliente es esencialmente una extrusión de un croquis. Por ejemplo, si un croquis estuviera formados por dos circunferencias concéntricas, y se utilizase la herramienta Saliente sobre dicho croquis, el resultado sería un cilindro:
Sketch (A) shown on the left; end result after pad operation (B) on the right.
v0.16 and below If the selected sketch is mapped to the face of an existing solid or another Part Design feature, the pad will be fused to it.
How to use
- Select the sketch to be padded. In v0.17 and above, a face on the existing solid can alternatively be used.
- Press the Pad button.
- Set the Pad parameters (see next section).
- Click OK.
Opciones
Cuando se crea un saliente, el letrero de diálogo de los 'parámetros del saliente' ofrece cinco diferentes formas de especificar la longitud a la cual el saliente se va a extruir
Tipo
Type offers five different ways of specifying the length to which the pad will be extruded.
Dimension
Introduce un valor numérico para la longitud del saliente. La dirección por defecto para la extrusión es saliendo del soporte, pero se puede cambiar seleccionando la opción Invertir. Las extrusiones se realizan normales normales al plano de definición del croquis.
Con la opción Simétrico al plano el saliente se extenderá la mitad de la dimensión indicada hacia cada lado del plano de croquis.
No es posible indicar dimensiones negativas. Utiliza en cambio la opción invertir.
Two dimensions
This allows to enter a second length in which the pad should extend in the opposite direction (into the support). Again can be changed by ticking the Reversed option.
To last
The pad will extrude up to the last face of the support in the extrusion direction. If there is no support, an error message will appear.
To first
The pad will extrude up to the first face of the support in the extrusion direction. If there is no support, an error message will appear.
Up to face
The pad will extrude up to a face in the support that can be chosen by clicking on it. If there is no support, no selections will be accepted.
Length
Defines the length of the pad. Multiple units can be used independently of the user's units preferences (m, cm, mm, nm, ft or ', in or ").
Symmetric to plane
Tick the checkbox to extend half of the given length to either side of the sketch plane.
Reversed
Reverses the direction of the pad.
Properties
- DatosRefine: v0.17 and above true or false. Cleans up residual edges left after the operation. This property is initially set according to the user's settings (found in Preferences → Part design → General → Model settings). It can be manually changed afterwards. This property will be saved with the FreeCAD document.
Limitaciones
- El algoritmo utilizado para Hasta el primero y Hasta el último:
- Crea una línea a través del centro de gravedad del croquis
- Encuentra todas las caras del soporte que se cortan por esta línea
- Selecciona la cara en la que el punto de intersección está más cerca/lejos del croquis
- Esto significa que la cara que se encuentre podría no siempre ser la que esperas. Si encuentras este problema, utiliza la opción Hasta la cara, y selecciona la cara que deseas.
- Para el caso particular de extrusión a una superficie cóncava, donde el croquis es más largo que esta superficie, la extrusión fallará. Este es un error sin resolver.
- No existe limpiado automático, por ejemplo, superficies planas adyacentes en una superficie individual. Puedes corregir esto manualmente en el entorno de Pieza con Refinar forma.
- Like all Part Design features, Pad creates a solid, thus the sketch must include a closed profile or it will fail with a Failed to validate broken face error. There can be multiple enclosed profiles inside a larger one, provided none intersect each other (for example, a rectangle with two circles inside it).
- The algorithm used for To First and To Last is:
- Create a line through the centre of gravity of the sketch
- Find all faces of the support cut by this line
- Choose the face where the intersection point is nearest/furthest from the sketch
- This means that the face that is found might not always be what you expected. If you run into this problem, use the Up to face type instead, and pick the face you want.
- For the very special case of extrusion to a concave surface, where the sketch is larger than this surface, extrusion will fail. This is a unresolved bug.
- v0.16 and below There is no automatic cleanup, e.g. of adjacent planar surfaces into a single surface. You can fix this manually in the Part workbench with Refine shape (which creates an unlinked, non-parametric solid) or with the Refine shape feature from the OpenSCAD Workbench which creates a parametric feature.
- Structure tools: Part, Group
- Helper tools: Create body, Create sketch, Edit sketch, Map sketch to face
- Modeling tools
- Datum tools: Create a datum point, Create a datum line, Create a datum plane, Create a local coordinate system, Create a shape binder, Create a sub-object(s) shape binder, Create a clone
- Additive tools: Pad, Revolution, Additive loft, Additive pipe, Additive helix, Additive box, Additive cylinder, Additive sphere, Additive cone, Additive ellipsoid, Additive torus, Additive prism, Additive wedge
- Subtractive tools: Pocket, Hole, Groove, Subtractive loft, Subtractive pipe, Subtractive helix, Subtractive box, Subtractive cylinder, Subtractive sphere, Subtractive cone, Subtractive ellipsoid, Subtractive torus, Subtractive prism, Subtractive wedge
- Transformation tools: Mirrored, Linear Pattern, Polar Pattern, Create MultiTransform, Scaled
- Dress-up tools: Fillet, Chamfer, Draft, Thickness
- Boolean: Boolean operation
- Extras: Migrate, Sprocket, Involute gear, Shaft design wizard
- Context menu: Set tip, Move object to other body, Move object after other object, Appearance, Color per face
- Getting started
- Installation: Download, Windows, Linux, Mac, Additional components, Docker, AppImage, Ubuntu Snap
- Basics: About FreeCAD, Interface, Mouse navigation, Selection methods, Object name, Preferences, Workbenches, Document structure, Properties, Help FreeCAD, Donate
- Help: Tutorials, Video tutorials
- Workbenches: Std Base, Arch, Assembly, CAM, Draft, FEM, Inspection, Mesh, OpenSCAD, Part, PartDesign, Points, Reverse Engineering, Robot, Sketcher, Spreadsheet, Surface, TechDraw, Test Framework
- Hubs: User hub, Power users hub, Developer hub