Draft Wire/cs: Difference between revisions

From FreeCAD Documentation
(Updating to match new version of source page)
(Updating to match new version of source page)
Line 12: Line 12:
# Stiskněte klávesu {{KEY|F}} nebo {{KEY|C}} nebo dvojklikněte na poslední bod pro ukončení nebo uzavření drátu. Je-li drát uzavřen, bude zároveň i povrchem i když se jeví jako drátový model.
# Stiskněte klávesu {{KEY|F}} nebo {{KEY|C}} nebo dvojklikněte na poslední bod pro ukončení nebo uzavření drátu. Je-li drát uzavřen, bude zároveň i povrchem i když se jeví jako drátový model.


==Volby==
==Options==
* If several connected [[Draft Line|Draft Lines]] are selected when pressing the '''Draft Wire''' Button, they will be turned into a wire and the command will exit. {{Version|0.17}}
* Stiskněte klávesu {{KEY|F}} nebo tlačítko {{KEY|[[Image:Draft FinishLine.png|12px]] '''[[Draft_FinishLine/cs|UkončitČáru]]'''}} pro ukončení drátu a ponechání jej otevřený
* Stiskněte klávesu {{KEY|C}} nebo tlačítko {{KEY|[[Image:Draft CloseLine.png|12px]] '''[[Draft_CloseLine/cs|UzavřítČáru]]'''}} nebo klikněte na první bod drátu. Tím se drát ukončí a uzavře se doplněním posledního (uzavíracího) segmentu mezi posledním a počátečním bodem.
* Press {{KEY|F}} or the {{KEY|[[Image:Draft FinishLine.png|12px]] '''[[Draft_FinishLine|Finish]]'''}} button to finish the wire, leaving it open
* Press {{KEY|C}} or the {{KEY|[[Image:Draft CloseLine.png|12px]] '''[[Draft_CloseLine|Close]]'''}} button or click on the first point to finish the wire, but making it closed by adding a last segment between the last point and the first one.
* Stisknutím klávesy {{KEY|X}}, {{KEY|Y}} nebo {{KEY|Z}} po zadání bodu zajistíte, že následující bod bude ležet na dané ose.
* Press {{KEY|X}}, {{KEY|Y}} or {{KEY|Z}} after a point to constrain the next point on the given axis.
* Pro ruční zadávání souřadnic jednoduše zadávejte čísla a mezi každou komponentou X, Y a Z stiskněte {{KEY|ENTER}}
* To enter coordinates manually, simply enter the numbers, then press {{KEY|ENTER}} between each X, Y and Z component.
* Stiskněte klávesu {{KEY|R}} nebo klikněte/odklikněte zaklikávací políčko {{KEY|'''Relativní'''}}. Je-li nastaven relativní mód jsou souřadnice následujícího bodu relativní k předchozímu bodu. Je-li mód absolutní souřadnice jsou vztaženy k počátečnímu bodu (0,0,0).
* Press {{KEY|R}} or click the checkbox to check/uncheck the {{KEY|'''Relative'''}} button. If relative mode is on, the coordinates of the next point are relative to the last one. If not, they are absolute, taken from the (0,0,0) origin point.
* Stiskněte klávesu {{KEY|T}} nebo klikněte/odklikněte zaklikávací políčko {{KEY|'''Pokračovat'''}}. Je-li nastaven pokračovací mód, nástroj Drát bude po ukončení drátu restartován a připraven ke kreslení dalšího drátu bez nutnosti znovu jej spouštět klikáním na tlačítko Drát.
* Press {{KEY|T}} or click the checkbox to check/uncheck the {{KEY|'''Continue'''}} button. If continue mode is on, the Wire tool will restart after you finish or close it, allowing you to draw another one without pressing the Wire button again.
* Stiskněte při kreslení klávesu {{KEY|CTRL}} pro [[Draft_Snap|přichycení]] Vašeho bodu k nejbližšímu uchopovacímu místu, nezávisle na vzdálenosti od něho.
* Press {{KEY|CTRL}} while drawing to force [[Draft_Snap|snapping]] your point to the nearest snap location, independently of the distance.
* Stiskněte při kreslení klávesu {{KEY|SHIFT}} pro nastavení [[Draft_Constrain|vazby]] Vašeho dalšího bodu vodorovně nebo svisle v relaci k předchozímu bodu.
* Press {{KEY|SHIFT}} while drawing to [[Draft_Constrain|constrain]] your next point horizontally or vertically in relation to the last one.
* Stiskněte klávesu {{KEY|W}} nebo stiskněte tlačítko {{KEY|[[Image:Draft Wipe.png|12px]] '''Smaž'''}} pro odstranění existujících segmentů a začněte křivku z posledního bodu.
* Stiskněte klávesy {{KEY|CTRL}}+{{KEY|Z}} nebo tlačítko {{KEY|[[Image:Draft UndoLine.png|12px]] '''[[Draft_UndoLine/cs|Undo]]'''}} k návratu na poslední bod.
* Press {{KEY|W}} or press the {{KEY|[[Image:Draft Wipe.png|12px]] '''Wipe'''}} button to remove the existing segments and start the wire from the last point.
* Press {{KEY|CTRL}}+{{KEY|Z}} or press the {{KEY|[[Image:Draft UndoLine.png|12px]] '''[[Draft_UndoLine|Undo]]'''}} button to undo the last point.
* Stiskněte klávesu {{KEY|I}} nebo tlačítko {{KEY|'''Filled'''}} aby se drát po jeho uzavření zobrazoval jako plocha. To jednoduše nastavuje Pohled->Vlastnost Drát na "Otevřené čáry" nebo "Drátový model", toto také může být snadno změněno později.
* Stiskněte klávesu {{KEY|ESC}} nebo tlačítko {{KEY|'''Cancel'''}} pro ukončení aktuálního příkazu Drát.
* Press {{KEY|I}} or the {{KEY|'''Filled'''}} button to have the wire filled with a face if it is closed.
* Press {{KEY|ESC}} or the {{KEY|'''Cancel'''}} button to abort the current Line command.
* Closed wires, when in "Flat Lines" display mode, can display a hatch pattern, by setting their "Pattern" property below.


==Properties==
==Properties==
Line 31: Line 33:
* {{PropertyData|Fillet Radius}}: Specifies a curvature radius to give to the nodes of the wire
* {{PropertyData|Fillet Radius}}: Specifies a curvature radius to give to the nodes of the wire
* {{PropertyData|Subdivisions}}: Divides the segments of the wire with the given number of subdivisions {{version|0.16}}
* {{PropertyData|Subdivisions}}: Divides the segments of the wire with the given number of subdivisions {{version|0.16}}
* {{PropertyData|Make Face}}: Fills the wire with a face if it is closed
* {{PropertyView|End Arrow}}: Shows an arrow symbol at the last point of the wire, so it can be used as an annotation leader line
* {{PropertyView|End Arrow}}: Shows an arrow symbol at the last point of the wire, so it can be used as an annotation leader line
* {{PropertyView|Pattern}}: Specifies a hatch pattern to fill the wire with (Closed Wire)
* {{PropertyView|Pattern}}: Specifies a hatch pattern to fill the wire with (Closed Wire)

Revision as of 17:42, 25 September 2016

Kreslení Drát

Umístění Menu
Kreslení -> Drát
Pracovní stoly
Kreslení, Architektura
Výchozí zástupce
W I
Představen ve verzi
-
Viz také
Kreslení Přímka, Kreslení B-křivka

Popis

Nástroj Drát vytváří lomenou čáru (sekvenci přímek z několika segmentů) v aktuální pracovní rovině. Použije se tloušťka čáry a barva předem zadaná v záložce Nástrojů. Nástroj Drát se chová přesně stejně jako nástroj Přímka kromě toho, že nekončí po zadání dvou bodů.

Použití

  1. Stiskněte tlačítko Drát nebo klávesy W potom I
  2. Klikněte na první bod ve 3D pohledu nebo zadejte jeho souřadnice
  3. Klikněte na další bod ve 3D pohledu nebo zadejte jeho souřadnice
  4. Stiskněte klávesu F nebo C nebo dvojklikněte na poslední bod pro ukončení nebo uzavření drátu. Je-li drát uzavřen, bude zároveň i povrchem i když se jeví jako drátový model.

Options

  • If several connected Draft Lines are selected when pressing the Draft Wire Button, they will be turned into a wire and the command will exit. introduced in version 0.17
  • Press F or the Finish button to finish the wire, leaving it open
  • Press C or the Close button or click on the first point to finish the wire, but making it closed by adding a last segment between the last point and the first one.
  • Press X, Y or Z after a point to constrain the next point on the given axis.
  • To enter coordinates manually, simply enter the numbers, then press ENTER between each X, Y and Z component.
  • Press R or click the checkbox to check/uncheck the Relative button. If relative mode is on, the coordinates of the next point are relative to the last one. If not, they are absolute, taken from the (0,0,0) origin point.
  • Press T or click the checkbox to check/uncheck the Continue button. If continue mode is on, the Wire tool will restart after you finish or close it, allowing you to draw another one without pressing the Wire button again.
  • Press CTRL while drawing to force snapping your point to the nearest snap location, independently of the distance.
  • Press SHIFT while drawing to constrain your next point horizontally or vertically in relation to the last one.
  • Press W or press the Wipe button to remove the existing segments and start the wire from the last point.
  • Press CTRL+Z or press the Undo button to undo the last point.
  • Press I or the Filled button to have the wire filled with a face if it is closed.
  • Press ESC or the Cancel button to abort the current Line command.
  • Closed wires, when in "Flat Lines" display mode, can display a hatch pattern, by setting their "Pattern" property below.

Properties

  • ÚdajeClosed: Specifies if the wire is closed or not
  • ÚdajeChamfer Size: Specifies the size of chamfered corners
  • ÚdajeFillet Radius: Specifies a curvature radius to give to the nodes of the wire
  • ÚdajeSubdivisions: Divides the segments of the wire with the given number of subdivisions introduced in version 0.16
  • ÚdajeMake Face: Fills the wire with a face if it is closed
  • PohledEnd Arrow: Shows an arrow symbol at the last point of the wire, so it can be used as an annotation leader line
  • PohledPattern: Specifies a hatch pattern to fill the wire with (Closed Wire)
  • PohledPattern Size: Specifies the size of the hatch pattern

See also Draft Pattern page.

Skriptování

Nástroj Drát může být využit v makrech a z konzoly Pythonu použitím následující funkce:

makeWire (list or Part.Wire, [closed], [placement], [facemode])
  • Vytvoří objekt Drát podle zadaného seznamu vektorů bodů nebo podle Drát (Part Wire).
  • Je-li closed True nebo jsou-li první a poslední bod identické, drát je uzavřen.
  • Je-li face (plocha) True (a drát je uzavřen), bude se drát jevit jako vyplněná plocha.
  • Je použita aktuálně nastavená tloušťka čáry a barva čáry.
  • Vrací nově vytvořený objekt.

Příklad:

import FreeCAD,Draft
p1 = FreeCAD.Vector(0,0,0)
p2 = FreeCAD.Vector(1,1,0)
p3 = FreeCAD.Vector(2,0,0)
Draft.makeWire([p1,p2,p3],closed=True)