Draft Snap/it: Difference between revisions
(Updating to match new version of source page) |
(Updating to match new version of source page) |
||
Line 11: | Line 11: | ||
{{TOCright}} |
{{TOCright}} |
||
<span id="Description"></span> |
|||
== Descrizione == |
== Descrizione == |
||
Line 42: | Line 43: | ||
* [[Image:Draft_Snap_Intersection.svg|32px]] [[Draft_Snap_Intersection|Snap Intersection]]: snaps to the intersection of two edges. |
* [[Image:Draft_Snap_Intersection.svg|32px]] [[Draft_Snap_Intersection|Snap Intersection]]: snaps to the intersection of two edges. |
||
* [[Image:Draft_Snap_Perpendicular.svg|32px]] [[Draft_Snap_Perpendicular|Snap Perpendicular]]: snaps to the perpendicular points on faces ({{Version| |
* [[Image:Draft_Snap_Perpendicular.svg|32px]] [[Draft_Snap_Perpendicular|Snap Perpendicular]]: snaps to the perpendicular points on faces ({{Version|0.21}}) and edges. |
||
* [[Image:Draft_Snap_Extension.svg|32px]] [[Draft_Snap_Extension|Snap Extension]]: snaps to an imaginary line that extends beyond the endpoints of straight edges. |
* [[Image:Draft_Snap_Extension.svg|32px]] [[Draft_Snap_Extension|Snap Extension]]: snaps to an imaginary line that extends beyond the endpoints of straight edges. |
||
Line 62: | Line 63: | ||
* [[Image:Draft_ToggleGrid.svg|32px]] [[Draft_ToggleGrid|Toggle Grid]]: switches the grid on or off. |
* [[Image:Draft_ToggleGrid.svg|32px]] [[Draft_ToggleGrid|Toggle Grid]]: switches the grid on or off. |
||
<span id="Advanced_snapping"></span> |
|||
<div class="mw-translate-fuzzy"> |
<div class="mw-translate-fuzzy"> |
||
=== Aggancio avanzato === |
=== Aggancio avanzato === |
||
Line 84: | Line 86: | ||
</div> |
</div> |
||
<span id="Preferences"></span> |
|||
<div class="mw-translate-fuzzy"> |
<div class="mw-translate-fuzzy"> |
||
==Opzioni== |
==Opzioni== |
Revision as of 19:46, 29 April 2023
Descrizione
Gli Ambiente Bozza strumenti consentono di scegliere punti e distanze cliccando sulla vista 3D con il puntatore, o inserendo le coordinate nel pannelo azioni dello strumento.
Snapping is available with most Draft and Arch commands.
Linea agganciata perpendicolarmente su un'altra linea
Snap tools
These tools are available in the Draft snap toolbar and in the Draft snap widget.
Note that circular edges do not have to be full circles.
- Snap Lock: enables or disables snapping globally.
- Snap Endpoint: snaps to the endpoints of edges.
- Snap Midpoint: snaps to the midpoint of edges.
- Snap Center: snaps to the center point of faces and circular edges, and to the DatiPlacement point of Draft WorkingPlaneProxies and Arch BuildingParts.
- Snap Angle: snaps to the special cardinal points on circular edges, at multiples of 30° and 45°.
- Snap Intersection: snaps to the intersection of two edges.
- Snap Perpendicular: snaps to the perpendicular points on faces (introduced in version 0.21) and edges.
- Snap Extension: snaps to an imaginary line that extends beyond the endpoints of straight edges.
- Snap Parallel: snaps to an imaginary line parallel to straight edges.
- Snap Special: snaps to special points defined by the object.
- Snap Near: snaps to the nearest point on faces and edges.
- Snap Ortho: snaps to imaginary lines that cross the previous point at multiples of 45°.
- Snap Grid: snaps to the intersections of grid lines.
- Snap WorkingPlane: projects snap points onto the current working plane.
- Snap Dimensions: shows temporary X and Y dimensions.
- Toggle Grid: switches the grid on or off.
Aggancio avanzato
- Ulteriori posizioni di aggancio possono essere ottenute combinando due metodi di snap, come Ortogonale e Estensione, che danno un punto di snap all'intersezione delle loro linee immaginarie.
- Altre posizioni di snap possono essere ottenute usando i Vincoli, tenendo premuto Maiusc o premendo X, Y o Z mentre si disegna.
- Premere Q mentre si disegna per inserire un "punto di attesa" nella posizione corrente del cursore. Dopo è possibile agganciarsi ortogonalmente a questi punti di attesa e alle intersezioni dei loro assi ortogonali. Se lo snap Punto medio è abilitato, è anche possibile agganciarsi al punto medio tra due punti di attesa. disponibile dalla versione 0.17
Snap cycling 1: The red rectangle was created first therefore it has snap priority. Without snap cycling you cannot snap to the green rectangle where it is overlapped by the red rectangle.
Snap cycling 2: After using the snap cycle key once the green rectangle receives snap priority. Snapping to the midpoint of the overlapped green edge is now possible.
Notes
Anche se l'utilizzo di molti metodi di snap allo stesso tempo può essere utile per disegnare gli oggetti nelle posizioni desiderate, può anche essere problematico se il cursore si collega costantemente ai punti sbagliati. In tal caso, provare a utilizzare solo un metodo di snap alla volta.
Opzioni
See also: Preferences Editor and Draft Preferences.
Note that after changing some preferences you must restart FreeCAD.
- La distanza massima a cui un punto è considerato un punto di snap è specificata nelle Preferenze di Draft, e può anche essere cambiato al volo premendo i tasti [ (aumenta) o ] (diminuisci).
- Premendo A mentre si disegna si blocca l'angolo corrente del segmento di linea disegnato.
- Drafting: Line, Polyline, Fillet, Arc, Arc by 3 points, Circle, Ellipse, Rectangle, Polygon, B-spline, Cubic Bézier curve, Bézier curve, Point, Facebinder, ShapeString, Hatch
- Annotation: Text, Dimension, Label, Annotation styles, Annotation scale
- Modification: Move, Rotate, Scale, Mirror, Offset, Trimex, Stretch, Clone, Array, Polar array, Circular array, Path array, Path link array, Point array, Point link array, Edit, Subelement highlight, Join, Split, Upgrade, Downgrade, Wire to B-spline, Draft to sketch, Set slope, Flip dimension, Shape 2D view
- Draft Tray: Select plane, Set style, Toggle construction mode, AutoGroup
- Snapping: Snap lock, Snap endpoint, Snap midpoint, Snap center, Snap angle, Snap intersection, Snap perpendicular, Snap extension, Snap parallel, Snap special, Snap near, Snap ortho, Snap grid, Snap working plane, Snap dimensions, Toggle grid
- Miscellaneous: Apply current style, Layer, Manage layers, Add a new named group, Move to group, Select group, Add to construction group, Toggle normal/wireframe display, Create working plane proxy, Heal, Show snap toolbar
- Additional: Constraining, Pattern, Preferences, Import Export Preferences, DXF/DWG, SVG, OCA, DAT
- Context menu:
- Layer container: Merge layer duplicates, Add new layer
- Layer: Activate this layer, Select layer contents
- Text: Open hyperlinks
- Wire: Flatten
- Working plane proxy: Write camera position, Write objects state
- Getting started
- Installation: Download, Windows, Linux, Mac, Additional components, Docker, AppImage, Ubuntu Snap
- Basics: About FreeCAD, Interface, Mouse navigation, Selection methods, Object name, Preferences, Workbenches, Document structure, Properties, Help FreeCAD, Donate
- Help: Tutorials, Video tutorials
- Workbenches: Std Base, Arch, Assembly, CAM, Draft, FEM, Inspection, Mesh, OpenSCAD, Part, PartDesign, Points, Reverse Engineering, Robot, Sketcher, Spreadsheet, Surface, TechDraw, Test Framework
- Hubs: User hub, Power users hub, Developer hub