Kreslení Bezierových křivek
Draft BezCurve |
Umístění Menu |
---|
Draft -> BezCurve |
Pracovní stoly |
Draft, Arch |
Výchozí zástupce |
B Z |
Představen ve verzi |
- |
Viz také |
Nikdo |
Popis
Nástroj Bezierova křivka vytváří Bezierovu křivku (nebo Bezierovu křivku po částech) z několika bodů v aktuální pracovní rovině. Přebírá tloušťku čáry a barvu předem nastavenou v záložce Nástroje.
The command creates a single Bézier curve with a ÚdajeDegree that is number_of_points - 1
. It can be transformed into a piecewise Bézier curve by reducing this property.
The Draft BezCurve and the Draft CubicBezCurve commands use control points to define the position and curvature of the spline. The Draft BSpline command, on the other hand, specifies the exact points through which the curve will pass.
Bézier curve defined by multiple points
See also: Draft Tray, Draft Snap and Draft Constrain.
- There are several ways to invoke the command:
- Press the Draft BezCurve button.
- Select the Drafting → Bézier tools → Bézier curve option from the menu.
- The Bézier curve task panel opens. See Options for more information.
- Pick the first point in the 3D view, or type coordinates and press the Enter point button.
- Pick additional points in the 3D view, or type coordinates and press the Enter point button.
- Press Esc or the Close button to finish the command.
Použití
- Stiskněte tlačítko Bezierova křivka nebo klávesy B potom Z
- Klikněte na první bod ve 3D pohledu nebo zadejte jeho souřadnice
- Klikněte na další bod ve 3D pohledu nebo zadejte jeho souřadnice
- Stiskněte klávesu F nebo C nebo dvojklikněte na poslední bod pro ukončení nebo na počáteční bod pro uzavření křivky.
Volby
The single character keyboard shortcuts available in the task panel can be changed. See Draft Preferences. The shortcuts mentioned here are the default shortcuts.
- Stiskněte tlačítko F nebo Dokončit pro ukončení křivky bez uzavření
- Stiskněte tlačítko C nebo Uzavřít nebo klikněte na první bod pro dokončení křivky s tím, že bude uzavřena a eventuálně bude přdán poslední segment do počátečního bodu.
- Stiskněte tlačítko X, Y nebo Z po vybrání bodu a pak bude další výběr proveden v dané ose.
- Pro ruční zadání souřadnic jednoduše vložte číslo a stiskněte ENTER mezi každou z komponent X, Y a Z.
- Stiskněte tlačítko R nebo zaklikněte/odklikněte políčko Relativně. Je-li zapnut relativní mód souřadnice následujícího bodu bodou relativní k předchozímu bodu, jinak budou absolutní k počátku (0,0,0).
- Stiskněte tlačítko T nebo zaklikněte/odklikněte políčko Pokračovat. Je-li zapnut pokračovací mód, bude nástroj Bezierova křivka po ukončení nebo uzavření křivky restartován a můžete hned kreslit další bez klikání na tlačítko pro Bezierovu křivku.
- Stiskněte při kreslení tlačítko CTRL chcete-li přichytit Váš bod k nejbližšímu uchopovacímu místu, nezávisle na tom jak je daleko.
- Stiskněte při kreslení tlačítko SHIFT pro nastavení vazby dalšího bodu svisle nebo vodorovně v relaci k poslednímu bodu.
- Stiskněte klávesu W nebo tlačítko Smazat pro smazání existujících segmentů a spuštění křivky od posledního bodu.
- Stiskněte klávesy CTRL+Z nebo tlačítko Undo pro vrácení k předchozímu bodu.
- Stiskněte klávesu ESC nebo tlačítko Zrušit k ukončení aktuálního příkazu pro Bezierovu křivku.
Notes
Omezení
- Tento nástroj je dostupný až od verze FreeCADu 0.14
- Vlastnost Body se zatím nezaobrazuje v seznamu vlastností.
- OpenCascade nepodporuje Bezierovy křivky se stupněm < 25. V praxi by to neměl být problém.
Preferences
See also: Preferences Editor and Draft Preferences.
- To change the number of decimals used for the input of coordinates: Edit → Preferences... → General → Units → Units settings → Number of decimals.
- To change the initial value of filled mode: Edit → Preferences... → Draft → General settings → Draft tools options → Fill objects with faces whenever possible. Changing the filled mode in a task panel will override this preference for the current FreeCAD session.
Vlastnosti
See also: Property editor.
A Draft BezCurve object is derived from a Part Part2DObject and inherits all its properties. It also has the following additional properties:
Data
Draft
- ÚdajeArea (
Area
): (read-only) specifies the area of the face of the curve. The value will be0.0
if ÚdajeMake Face iffalse
or the face cannot be created. - ÚdajeClosed (
Bool
): specifies if the curve is closed or not. If the curve is initially open this value isfalse
, setting it totrue
will draw a segment to close the curve. If the curve is initially closed this value istrue
, setting it tofalse
will remove the last segment and make the curve open. - ÚdajeContinuity (
IntegerList
): (read-only) specifies the continuity of the curve. - ÚdajeDegree (
Integer
): specifies the degree of the curve. - ÚdajeLength (
Length
): (read-only) specifies the total length of the curve. - ÚdajeMake Face (
Bool
): specifies if the curve makes a face or not. If it istrue
a face is created, otherwise only the perimeter is considered part of the object. This property only works if ÚdajeClosed istrue
and if the curve does not self-intersect. - ÚdajePoints (
VectorList
): specifies the control points of the curve in its local coordinate system.
View
Draft
- PohledArrow Size (
Length
): specifies the size of the symbol displayed at the end of the curve. - PohledArrow Type (
Enumeration
): specifies the type of symbol displayed at the end of the curve, which can beDot
,Circle
,Arrow
,Tick
orTick-2
. - PohledEnd Arrow (
Bool
): specifies whether to show a symbol at the end of the curve, so it can be used as an annotation line. - PohledPattern (
Enumeration
): specifies the Draft Pattern with which to fill the face of the closed curve. This property only works if ÚdajeMake Face istrue
and if PohledDisplay Mode isFlat Lines
. - PohledPattern Size (
Float
): specifies the size of the Draft Pattern.
Scripting
Skriptování
Nástroj Bezierova křivka může být využit v makrech a z konzoly Pythonu použitím následující funkce:
bezcurve = make_bezcurve(pointslist, closed=False, placement=None, face=None, support=None, degree=None)
bezcurve = make_bezcurve(Part.Wire, closed=False, placement=None, face=None, support=None, degree=None)
- Vytvoří objekt Bezierovy křivky podle zadaného seznamu vektorů. Místo seznamu bodů můžete také vložit díl Drát.
Example:
import FreeCAD as App
import Draft
doc = App.newDocument()
p1 = App.Vector(0, 0, 0)
p2 = App.Vector(1000, 1000, 0)
p3 = App.Vector(2000, 0, 0)
p4 = App.Vector(1500, -2000, 0)
bezcurve1 = Draft.make_bezcurve([p1, p2, p3, p4], closed=True)
bezcurve2 = Draft.make_bezcurve([p4, 1.3*p2, p1, 4.1*p3], closed=True)
bezcurve3 = Draft.make_bezcurve([1.7*p3, 1.5*p4, 2.1*p2, p1], closed=True)
doc.recompute()
- Drafting: Line, Polyline, Fillet, Arc, Arc by 3 points, Circle, Ellipse, Rectangle, Polygon, B-spline, Cubic Bézier curve, Bézier curve, Point, Facebinder, ShapeString, Hatch
- Annotation: Text, Dimension, Label, Annotation styles, Annotation scale
- Modification: Move, Rotate, Scale, Mirror, Offset, Trimex, Stretch, Clone, Array, Polar array, Circular array, Path array, Path link array, Point array, Point link array, Edit, Subelement highlight, Join, Split, Upgrade, Downgrade, Wire to B-spline, Draft to sketch, Set slope, Flip dimension, Shape 2D view
- Draft Tray: Select plane, Set style, Toggle construction mode, AutoGroup
- Snapping: Snap lock, Snap endpoint, Snap midpoint, Snap center, Snap angle, Snap intersection, Snap perpendicular, Snap extension, Snap parallel, Snap special, Snap near, Snap ortho, Snap grid, Snap working plane, Snap dimensions, Toggle grid
- Miscellaneous: Apply current style, Layer, Manage layers, Add a new named group, Move to group, Select group, Add to construction group, Toggle normal/wireframe display, Create working plane proxy, Heal, Show snap toolbar
- Additional: Constraining, Pattern, Preferences, Import Export Preferences, DXF/DWG, SVG, OCA, DAT
- Context menu:
- Layer container: Merge layer duplicates, Add new layer
- Layer: Activate this layer, Select layer contents
- Text: Open hyperlinks
- Wire: Flatten
- Working plane proxy: Write camera position, Write objects state
- Getting started
- Installation: Download, Windows, Linux, Mac, Additional components, Docker, AppImage, Ubuntu Snap
- Basics: About FreeCAD, Interface, Mouse navigation, Selection methods, Object name, Preferences, Workbenches, Document structure, Properties, Help FreeCAD, Donate
- Help: Tutorials, Video tutorials
- Workbenches: Std Base, Arch, Assembly, CAM, Draft, FEM, Inspection, Mesh, OpenSCAD, Part, PartDesign, Points, Reverse Engineering, Robot, Sketcher, Spreadsheet, Surface, TechDraw, Test Framework
- Hubs: User hub, Power users hub, Developer hub