Draft Arc/es: Difference between revisions

From FreeCAD Documentation
(Created page with "==Descripción== La herramienta arco crea un arco en el plano de trabajo actual introduciendo cuatro puntos, el centro, el radio, el primer punto y ...")
(Created page with "==Utilización== # Presiona el botón {{KEY|16px Arco}}, o presiona las teclas {{KEY|A}} y {{KEY|R}} # Indica un primer punto en la v...")
Line 7: Line 7:
[[Image:Draft_Arc_example.jpg|400px]]
[[Image:Draft_Arc_example.jpg|400px]]


==How to use==
==Utilización==

# Press the {{KEY|[[Image:Draft Arc.png|16px]] [[Draft Arc]]}} button, or press {{KEY|A}} then {{KEY|R}} keys
# Presiona el botón {{KEY|[[Image:Draft Arc.png|16px]] [[Draft Arc/es|Arco]]}}, o presiona las teclas {{KEY|A}} y {{KEY|R}}
# Click a first point on the 3D view, or type a [[Draft_Coordinates|coordinate]]
# Indica un primer punto en la vista 3D, o escribe unas [[Draft_Coordinates/es|coordenadas]]
# Click a second point on the 3D view, or enter a radius value
# Indica un segundo punto en la vista 3D, o introduce el valor del radio
# Click a third point in the 3D view, or enter a start angle
# Indica un tercer punto en la vista 3D, o introduce un ángulo de inicio
# Click a fourth point in the 3D View, or enter an end ange
# Indica un cuarto punto en la vista 3D, o introduce un ángulo final


==Options==
==Options==

Revision as of 20:32, 9 January 2014

Draft_Arc

Ubicación en el Menú
Croquis → Arco
Entornos de trabajo
Croquis, Arquitectura
Atajo de teclado por defecto
A R
Introducido en versión
-
Ver también
Circunferencia

Descripción

La herramienta arco crea un arco en el plano de trabajo actual introduciendo cuatro puntos, el centro, el radio, el primer punto y el último punto, o seleccionando tangencias, o cualquier combinación de ellas. Toma el espesor de línea y color previamente definidos en la pestaña de tareas. Esta herramienta funciona del mismo modo que la herramienta circunferencia, pero añade los ángulos inicial y final.

Utilización

  1. Presiona el botón Arco, o presiona las teclas A y R
  2. Indica un primer punto en la vista 3D, o escribe unas coordenadas
  3. Indica un segundo punto en la vista 3D, o introduce el valor del radio
  4. Indica un tercer punto en la vista 3D, o introduce un ángulo de inicio
  5. Indica un cuarto punto en la vista 3D, o introduce un ángulo final

Options

  • The primary use of the arc tool is by picking four points: the centre, a point on the circumference, defining the radius, a third point defining the start of the arc, and a fourth one defining its end.
  • By pressing ALT, you can select a tangent instead of picking point, to define the base circle of the arc. You can therefore construct several types of circles by selecting one, two or three tangents.
  • The direction of the arc depends on the movement you are doing with your mouse. If you start to move clockwise after the third point is entered, your arc will go clockwise. To go counter-clockwise, simply move your mouse back over the third point, until the arc starts drawing in the other direction.
  • To enter coordinates manually, simply enter the numbers, then press ENTER between each X, Y and Z component.
  • Press T or click the checkbox to check/uncheck the Continue button. If continue mode is on, the Arc tool will restart after you give the fourth point, allowing you to draw another arc without pressing the Arc button again.
  • Press CTRL while drawing to force snapping your point to the nearest snap location, independently of the distance.
  • Press SHIFT while drawing to constrain your point horizontally or vertically in relation to the center.
  • Press ESC or the Cancel button to abort the current Line command.
  • The arc can be turned into a circle after creation, by setting a same value to its first angle and last angle properties.

Properties

  • DatosRadius: The radius of the arc
  • DatosFirst Angle: The angle of the first point of the arc
  • DatosLast Angle: The angle of the last point of the arc

Scripting

The Circle tool can also be used to create arcs in macros and from the python console by using the following function, giving it additional arguments:

 '''makeCircle (radius, [placement], [facemode], [startangle], [endangle])'''
  • Creates a circle object with given radius.
  • If a placement is given, it is used. If facemode is False, the circle is shown as a wireframe, otherwise as a face.
  • If startangle AND endangle are given (in degrees), they are used and the object appears as an arc.
  • Returns the newly created object.

Example:

 import Draft
 myArc = Draft.makeCircle(2,startangle=0,endangle=90)