Arch Stairs
Arch Stairs |
Меню прокату |
---|
Arch → Stairs |
Верстаки |
Arch |
Ярлик за умовчанням |
S R |
Введено у версії |
- |
Дивись також |
Жоден |
Description
The Arch Stairs tool allows you to build automatically several types of stairs. At the moment, only straight stairs (with or without a central landing) are supported. Stairs can be built from scratch, or from a straight Draft Line, in which case the stairs follow the line. If the line is not horizontal but has a vertical inclination, the stairs will also follow its slope.
See the Stairs entry in wikipedia for a definition of the different terms used to describe parts of stairs.
Two constructed stairs, one with a massive structure and a landing, and another one with a single stringer.
Options
- Stairs share the common properties and behaviors of all Arch Components
Usage
- Press the Arch Stairs button, or press S, R keys.
- Adjust the desired properties. Some parts of the stairs, such as the structure, might not appear immediately, if any of the properties makes it impossible, such as a structure thickness of 0.
Properties
Data
Segment and Parts
- ДаніAbs Top (
Vector
): (read-only) The absolute top level the stairs lead to. - ДаніLast Segment (
Link
): Last segment (flight or landing) of an Arch Stairs connecting to this segment. The start level of the stairs will be the end level of this last segment. - ДаніOutline Left (
VectorList
): The left outline of the stairs. - ДаніOutline Left All (
VectorList
): The left outline of all segments of the stairs. - ДаніOutline Right (
VectorList
): The right outline of the stairs. - ДаніOutline Right All (
VectorList
): The right outline of all segments of the stairs. - ДаніRailing Height Left (
Length
): Height of the left railing of the stairs or landing. - ДаніRailing Height Right (
Length
): Height of the right railing of the stairs or landing. - ДаніRailing Left (
String
): Name of the left railing object. - ДаніRailing Offset Left (
Length
): Offset of the left railing from the edge of the stairs or landing. - ДаніRailing Offset Right (
Length
): Offset of the right railing from the edge of the stairs or landing. - ДаніRailing Right (
String
): Name of the right railing object.
Stairs
- ДаніAlign (
Enumeration
): The alignment of the stairs on the baseline. Only used if a baseline is defined. Can beLeft
,Right
orCenter
. - ДаніHeight (
Length
): The total height of the stairs. Only used if no baseline is defined, or if the baseline is horizontal. Ignored if ДаніRiser Height Enforce is non-zero. - ДаніLength (
Length
): The total length of the stairs if no baseline is defined. Ignored if ДаніTread Depth Enforce is non-zero. - ДаніWidth (
Length
): The width of the stairs. - ДаніWidth of Landing (
FloatList
): If the ДаніNumber Of Steps is 1, the stairs object acts as a landing. When this is the case and the baseline is multi-segment, the width of first segment of the landing follows the ДаніWidth, the widths of subsequent segments follow the list set here.
Steps
- ДаніBlondel Ratio (
Float
): (read-only) The calculated Blondel ratio. This ratio indicates comfortable stairs and should be between 62 and 64cm or 24.5 and 25.5in. - ДаніLanding Depth (
Length
): The depth of the landing of the flight, if enabled in ДаніLandings. Defaults to the ДаніWidth if 0. - ДаніNosing (
Length
): The size of the nosing. - ДаніNumber Of Steps (
Integer
): The numbers of steps (risers). - ДаніRiser Height (
Length
): (read-only) The height of the risers. If ДаніRiser Height Enforce is 0 it is calculated (ДаніHeight / ДаніNumber of Steps). Else it is the same as ДаніRiser Height Enforce. - ДаніRiser Height Enforce (
Length
): The enforced height of the risers. - ДаніRiser Thickness (
Length
): The thickness of the risers. - ДаніTread Depth (
Length
): (read-only) The depth of the treads. If ДаніTread Depth Enforce is 0 it is calculated (ДаніLength / ДаніNumber of Steps). Else it is the same as ДаніTread Depth Enforce. - ДаніTread Depth Enforce (
Length
): The enforced depth of the treads. - ДаніTread Thickness (
Length
): The thickness of the treads.
Structure
- ДаніConnection Down Start Stairs (
Enumeration
): The type of connection between the lower floor slab and the start of the stairs. Can beHorizontalCut
,VerticalCut
orHorizontalVerticalCut
. - ДаніConnection End Stairs Up (
Enumeration
): The type of connection between the end of the stairs and the upper floor slab. Can betoFlightThickness
ortoSlabThickness
. - ДаніDown Slab Thickness (
Length
): The thickness of the lower floor slab. - ДаніFlight (
Enumeration
): The direction of the flight after the landing. Can beStraight
,HalfTurnLeft
orHalfTurnRight
. - ДаніLandings (
Enumeration
): The type of landings. Can beNone
orAt center
(At each corner
not implemented yet). - ДаніStringer Overlap (
Length
): The overlap of the stringers above the bottom of the treads. - ДаніStringer Width (
Length
): The width of the stringers. - ДаніStructure (
Enumeration
): The structure type of the stairs. Can beNone
,Massive
,One stringer
orTwo stringers
. - ДаніStructure Offset (
Length
): The offset between the border of the stairs and the structure. - ДаніStructure Thickness (
Length
): The thickness of the structure. - ДаніUp Slab Thickness (
Length
): The thickness of the upper floor slab. - ДаніWinders (
Enumeration
): The type of winders. Not implemented.
Limitations
- Only straight stairs are available at the moment
- See the forum entry for circle stairs.
- See the forum announcement.
Scripting
See also: Arch API and FreeCAD Scripting Basics.
The Stairs tool can be used in macros and from the Python console by using the following function:
Stairs = makeStairs(baseobj=None, length=None, width=None, height=None, steps=None, name="Stairs")
- Creates a
Stairs
object from the givenbaseobj
. - If
baseobj
is not given, it will uselength
,width
,height
, andsteps
, to build a solid object.
Example:
import Arch
Stairs = Arch.makeStairs(length=5000, width=1200, height=3000, steps=14)
- Elements: Wall, Structure, Curtain Wall, Window, Roof, Space, Stairs, Equipment, Frame, Fence, Truss, Profile, Pipe, Pipe Connector
- Reinforcements: Straight Rebar, U-Shape Rebar, L-Shape Rebar, Stirrup, Bent-Shape Rebar, Helical Rebar, Column Reinforcement, Beam Reinforcement, Slab Reinforcement, Footing Reinforcement, Custom Rebar
- Panels: Panel, Panel Cut, Panel Sheet, Nest
- Materials: Material, Multi-Material
- Organization: Building Part, Project, Site, Building, Level, External reference, Section Plane, Schedule
- Axes: Axis, Axes system, Grid
- Modification: Cut with plane, Add component, Remove component, Survey
- Utilities: Component, Clone component, Split Mesh, Mesh to Shape, Select non-manifold meshes, Remove Shape from Arch, Close Holes, Merge Walls, Check, Toggle IFC Brep flag, 3 Views from mesh, Create IFC spreadsheet, Toggle Subcomponents
- Additional: Preferences, Import Export Preferences (IFC, DAE, OBJ, JSON, 3DS, SHP), IfcOpenShell, IfcPlusPlus, Arch API
- Getting started
- Installation: Download, Windows, Linux, Mac, Additional components, Docker, AppImage, Ubuntu Snap
- Basics: About FreeCAD, Interface, Mouse navigation, Selection methods, Object name, Preferences, Workbenches, Document structure, Properties, Help FreeCAD, Donate
- Help: Tutorials, Video tutorials
- Workbenches: Std Base, Arch, Assembly, CAM, Draft, FEM, Inspection, Mesh, OpenSCAD, Part, PartDesign, Points, Reverse Engineering, Robot, Sketcher, Spreadsheet, Start, Surface, TechDraw, Test Framework, Web
- Hubs: User hub, Power users hub, Developer hub