Draft: Filament/Polilinie
Draft Wire |
poziția meniului |
---|
Draft → Wire |
Ateliere |
Draft, Arch |
scurtătură |
W I |
Prezentat în versiune |
- |
A se vedea, de asemenea, |
Draft Line, Draft BSpline |
Descriere
Unealta filament "Wire" creează o polilinie (o succesiune de segmente legate între ele) în planul de lucru curent. Preia valorile pentru lăţimea și culoarea liniei setate în prealabil pe tab-ul "Sarcini" (Tasks). Unealta "Wire" se comportă ca şi unealta linie din CIornă, cu deosebirea că va continua şi după trasarea între primele două puncte.
The Draft BSpline tool behaves like the Wire tool, except that each of its segments is curved instead of being a straight line. Use Draft WireToBSpline to convert one to the other.
Cum se foloseşte
- Apăsați tasta Draft Wire button, or press W then I sau apăsați W apoi tastele I
- Faceți clic pe un prim punct din vizualizarea 3D sau tastați un coordinate
- Faceți clic pe un punct suplimentar în vizualizarea 3D sau tastați un coordinate
- Apăsați F sau C sau faceți dublu clic pe ultimul punct sau faceți clic pe primul punct pentru a termina sau a închide filamentul/polilinia. Dacă filamentul este închis, acesta va fi, de asemenea, o fațetă, chiar dacă acesta apare ca o rețea wireframe.
The wire can be edited by double clicking on the element in the tree view, or by pressing the Draft Edit button. Then you can move the points to a new position, or click add point or remove point and then click on the wire to add or remove points.
Fuse single lines
If several connected Draft Lines are selected when pressing the Draft Wire button, they will be turned into a wire and the command will exit. introduced in version 0.17
Note: the end points of the lines must be exactly touching or they won't merge. If necessary, manually adjust the Draft Coordinates of the start and end points of the lines, or use Draft Snap with the Draft Endpoint mode to make the nodes coincident.
Opțiuni
- Dacă sunt selectate mai multe linii Draft Lines atunci când apăsați butonul Draft Wire, acestea vor fi transformate într-un fir și comanda va ieși. introduced in version 0.17/ro
- Apăsați butonul F sau butonul Finish pentru a finalize firul și a-l lăsa deschis
- Apăsați butonul C or the Close terminați firul, dar închizându-l prin adăugarea unui ultim segment între ultimul punct și primul.
- Apăsați X, Y sau Z după un punct pentru a restrânge următorul punct de pe axa dată.
- Pentru a introduce manual coordonatele, pur și simplu introduceți numerele, apoi apăsați ENTER între fiecare componentă X, Y și Z.
- Apăsați tasta R sau faceți clic pe caseta de selectare pentru a bifa/debifa butonul Relativ. Dacă modul relativ este activ, coordonatele punctului următor sunt relative la ultimul. Dacă nu, ele sunt absolute, luate din punctul de origine (0,0,0).
- Apăsați tasta T sau faceți clic pe caseta de selectare pentru a bifa/debifa butonul Continue. Dacă funcția continuă este activată, instrumentul Wire se va reporni după ce terminați sau închideți-l, permițându-vă să desenați altul fără să apăsați din nou butonul Wire.
- Apăsați CTRL în timp ce desenați pentru a forța ancorarea snapping punctului dvs. către cea mai apropiată locație, independent de distanța.
- Apăsați pe SHIFT în timp ce desenați constrain următorul punct pe orizontală sau pe verticală în raport cu ultimul.
- Apăsați butonul W sau apăsați butonul Șterge pentru a elimina segmentele existente și a porni firul de la ultima punct.
- Apăsați tasta CTRL + Z sau apăsați pe Undo pentru a anula ultimul punct.
- Apăsați butonul I sau butonul Fillet pentru a avea firul umplut cu o fațetă dacă este închis.
- Apăsați butonul ESC sau butonul Cancel pentru a întrerupe comanda curentă.
- Firele închise, atunci când sunt în modul de afișare "Flat Lines", pot afișa un model de hașură, prin setarea proprietății "Pattern" de mai jos.
Proprietăți
- DATEClosed: Specifică dacă firul este închis sau nu
- DATEChamfer Size: Specifică dimensiunea colțurilor zimțate
- DATEFillet Radius: Specifică o rază de curbură pentru a da nodurilor sârmei
- DATESubdivisions: Separă segmentele firului cu numărul de subdiviziuni date introduced in version 0.16/ro
- DATEMake Face: Umple firul cu o față dacă este închis
- VEDEREEnd Arrow: Arată un simbol săgeată în ultimul punct al firului, astfel încât acesta poate fi folosit ca linie de lider de adnotări
- VEDEREPattern: Specifică un model de trasare pentru a umple firul cu (Sârmă închisă)
- VEDEREPattern Size: Specifică dimensiunea șablonului de trasare
Data
- DateStart: specifies the first point in the wire.
- DateEnd: specifies the last point in the wire, not counting the initial point if the wire is closed.
- DateClosed: specifies if the wire is closed or not. If the wire is initially open, this value is
false
; setting it totrue
will draw a line segment to close the wire. If the wire is initially closed, this value istrue
; setting it tofalse
will remove the last line segment, and make the wire open. - DateChamfer Size: specifies the size of the chamfers (straight segments) created on the corners of the wire.
- DateFillet Radius: specifies the radius of the fillets (arc segments) created on the corners of the wire.
- DateMake Face: specifies if the wire makes a face or not. If it is
true
a face is created, otherwise only the edges are considered part of the object. This property only works if DateClosed istrue
.
- Note: do not set DateMake Face to
true
if the wire intersects itself, as it won't create a proper face.
- DateSubdivisions: specifies the number of interior nodes in each segment of the wire. introduced in version 0.16
- DateLength: (read-only) specifies the length of the entire wire.
View
- VizualizareEnd Arrow: if it is
true
it will display a symbol at the last point of the wire, so it can be used as an annotation line. - VizualizareArrow Size: specifies the size of the symbol displayed at the end of the wire.
- VizualizareArrow Type: specifies the type of symbol displayed at the end of the wire, which can be "Dot", "Circle", "Arrow", or "Tick".
- VizualizarePattern: specifies a Draft Pattern with which to fill the face of the closed wire. This property only works if DateMake Face is
true
, and if VizualizareDisplay Mode is "Flat Lines". - VizualizarePattern Size: specifies the size of the Draft Pattern.
Script-Programare
A se vedea FreeCAD Scripting Basics pentru mai multe informații
Instrumentul Wire tool poate fi utilizat în macros și de la consola Python utilizând următoarele funcții:
Wire = makeWire(pointslist, closed=False, placement=None, face=None, support=None)
Wire = makeWire(Part.Wire, closed=False, placement=None, face=None, support=None)
- Creează un obiect
Wire
din lista dată de vectori sau din lista de puncte datepointslist
.- Dacă închis este Adevărat sau dacă primele și ultimul puncte sunt identice, firul este închis.
- Each point in the list is defined by its
FreeCAD.Vector
- Alternatively, the input can be a
Part.Wire
, from which points are extracted - Dacă
closed
esteTrue
(și firul este închis, (primul și ultimul punct sunt identice)), firul va forma o fațetă.
- Alternatively, the input can be a
- Se va folosi versiunea curentă de linie și culoareDraft Linestyle.
- Returnează obiectul nou creat.
Exempluː
import FreeCAD, Draft
p1 = FreeCAD.Vector(0, 0, 0)
p2 = FreeCAD.Vector(1000, 1000, 0)
p3 = FreeCAD.Vector(2000, 0, 0)
Wire1 = Draft.makeWire([p1, p2, p3], closed=True)
Wire2 = Draft.makeWire([p1, 2*p3, 1.3*p2], closed=True)
Wire3 = Draft.makeWire([1.3*p3, p1, -1.7*p2], closed=True)
- Drafting: Line, Polyline, Fillet, Arc, Arc by 3 points, Circle, Ellipse, Rectangle, Polygon, B-spline, Cubic Bézier curve, Bézier curve, Point, Facebinder, ShapeString, Hatch
- Annotation: Text, Dimension, Label, Annotation styles, Annotation scale
- Modification: Move, Rotate, Scale, Mirror, Offset, Trimex, Stretch, Clone, Array, Polar array, Circular array, Path array, Path link array, Point array, Point link array, Edit, Subelement highlight, Join, Split, Upgrade, Downgrade, Wire to B-spline, Draft to sketch, Set slope, Flip dimension, Shape 2D view
- Draft Tray: Select plane, Set style, Toggle construction mode, AutoGroup
- Snapping: Snap lock, Snap endpoint, Snap midpoint, Snap center, Snap angle, Snap intersection, Snap perpendicular, Snap extension, Snap parallel, Snap special, Snap near, Snap ortho, Snap grid, Snap working plane, Snap dimensions, Toggle grid
- Miscellaneous: Apply current style, Layer, Manage layers, Add a new named group, Move to group, Select group, Add to construction group, Toggle normal/wireframe display, Create working plane proxy, Heal, Show snap toolbar
- Additional: Constraining, Pattern, Preferences, Import Export Preferences, DXF/DWG, SVG, OCA, DAT
- Context menu:
- Layer container: Merge layer duplicates, Add new layer
- Layer: Activate this layer, Select layer contents
- Text: Open hyperlinks
- Wire: Flatten
- Working plane proxy: Write camera position, Write objects state
- Getting started
- Installation: Download, Windows, Linux, Mac, Additional components, Docker, AppImage, Ubuntu Snap
- Basics: About FreeCAD, Interface, Mouse navigation, Selection methods, Object name, Preferences, Workbenches, Document structure, Properties, Help FreeCAD, Donate
- Help: Tutorials, Video tutorials
- Workbenches: Std Base, Assembly, BIM, CAM, Draft, FEM, Inspection, Mesh, OpenSCAD, Part, PartDesign, Points, Reverse Engineering, Robot, Sketcher, Spreadsheet, Surface, TechDraw, Test Framework
- Hubs: User hub, Power users hub, Developer hub