Introduction to Python/ko: Revision history

Diff selection: Mark the radio buttons of the revisions to compare and hit enter or the button at the bottom.
Legend: (cur) = difference with latest revision, (prev) = difference with preceding revision, m = minor edit.

2 June 2024

  • curprev 08:0108:01, 2 June 2024Urstein talk contribs 22,245 bytes +162 Created page with "일반적으로 컴퓨터 프로그램을 작성할 때 텍스트 편집기나 특수 프로그래밍 환경(기본적으로 몇 가지 추가 도구가 포함된 텍스트 편집기)을 열고 프로그램을 작성한 다음 컴파일하고 실행합니다. 입력하는 동안 하나 이상의 오류가 발생하여 프로그램이 작동하지 않는 경우가 많습니다. 무엇이 잘못되었는지 알려주는 오류 메시지가 나타날 수도 있습니다...."
  • curprev 08:0008:00, 2 June 2024Urstein talk contribs 22,083 bytes +31 Created page with "== 통역기 =="
  • curprev 08:0008:00, 2 June 2024Urstein talk contribs 22,052 bytes −9 No edit summary
  • curprev 07:5907:59, 2 June 2024Urstein talk contribs 22,061 bytes 0 No edit summary
  • curprev 07:5907:59, 2 June 2024Urstein talk contribs 22,061 bytes +11 Created page with "다음은 매우 기본적인 소개일 뿐 완전한 자습서는 아닙니다. 그러나 이것이 FreeCAD와 그 메커니즘에 대한 추가 탐구를 위한 좋은 출발점이 되기를 바랍니다.파이썬 해석기에 아래 코드 조각을 입력하는 것이 좋습니다."
  • curprev 07:5807:58, 2 June 2024Urstein talk contribs 22,050 bytes +636 No edit summary
  • curprev 07:5607:56, 2 June 2024Urstein talk contribs 21,414 bytes −488 Created page with "*인간이 읽을 수 있도록 설계되어 상대적으로 배우고 이해하기 쉽습니다. *하나씩 해석됩니다. 이는 프로그램을 실행하기 전에 컴파일할 필요가 없음을 의미합니다. 원하는 경우 파이썬 코드를 한 줄씩 즉시 실행할 수도 있습니다."
  • curprev 07:5507:55, 2 June 2024Urstein talk contribs 21,902 bytes −67 Created page with "이것은 [https://en.wikipedia.org/wiki/Python_%28programming_언어%29 파이썬]을 처음 접하는 사람들을 위한 짧은 자습서입니다. 파이썬은 오픈 소스, 다중 플랫폼[https://en.wikipedia.org/wiki/Programming_언어 프로그래밍 언어]입니다."
  • curprev 07:5407:54, 2 June 2024Urstein talk contribs 21,969 bytes −21 No edit summary
  • curprev 07:5407:54, 2 June 2024Urstein talk contribs 21,990 bytes +26 Created page with "==소개=="
  • curprev 07:5307:53, 2 June 2024Urstein talk contribs 21,964 bytes +24 No edit summary

17 February 2023

23 June 2022

22 October 2021

30 December 2020

5 June 2020

28 May 2020

22 May 2020

25 September 2019

27 June 2019